TRUCK EXPLORER STANDARD 2021
Description
Truck Explorer Standard equipment consists of the most general purposes for trucks. You could work via OBD or directly connect to the ECU on the board covering the DirectConnect 2U tool.
Include Licenses:
1. License MB MEMO
The license permits to Read/Write FLASH and EEPROMs of the MR (PLD) control unit.
Additionally, it is possible to connect to the system through:
— OBD (MR is attached inside truck) or
— through connection with DirectConnect 2M tool (MR is placed on your board).
This function is handy for Chiptuning works and improving units after the broken update. OBD performs all transactions, and there is no need to decapsulate/open the unit, so the unit stays in factory position, and therefore, no guarantee is voided.
This function permits cloning MR. For example, you read one MR, save it to *.bin file, and write it to another MR.
2. License MB KEYS
MB Keys learn — permits to figure new keys for the vehicle above OBD (MR (PLD) control unit). No extra equipment is used; all transactions are arranged offline, the only connection to the vehicle is needed.
It is possible to add a new key, delete useless keys while compared to the unit through:
— OBD (MR is attached inside truck) or
— through connection with DirectConnect 2M tool (MR is placed on your board).
Disable immobilizer within FR and MR. IMMO OFF.
3. License MB CALC
MB VeDoc, FDOK calculators — adds entrance digests for VeDoc and FDOK algorithms for MR (PLD) control unit.
Must be practiced together with XENTRY (DAS) software and fit diagnostic tool where these codes are asked. All transactions are prepared offline—only connection to the vehicle required for VEDOC.
For FDOK calculations needed no connection to the vehicle. FDOK code for current and old DAS.
DAS password generator — calculates password required by DAS to reach some specific purposes (MR downgrade of Euro 4, 5 to Euro 3, etc. Disable AdBlue)
4. License FR
The license permits reaching FR. Promoted FMR; FR; FR/CPC; CPC1EU; CPC2EU. Immo off in FR.
5. License 2011+
For PLD, read and write action (category memo) PLD with XC2287 protected microprocessor, made in 2011 and following. The license permits reaching firmware 22B, 23E, 24B from 2011.
Continental Euro5 PLD: (MCU XC2287, 1 EEPROM M95640). Not locked processor supported.
*MB MEMO - license needed.
6. License 2014+
For PLD memory, read and write transaction (category memo) PLD with XC2287 secured microprocessor.
The license permits reaching firmware 21x, 23 °F, 24 °C, 25x, 26x from the 2014 year. In addition, open access Read/Write memory for PLD, made in 2014 and following, including Infineon (XC2287) microprocessor.
Continental Euro5 PLD: 1 EEPROM M95640, MCU XC2287 (flash 768kB). Locked processor approved.
PLD must be opened. The support team will fit a manual.
*MB MEMO License and DirectConnect2M tool are needed.
7. License 2018+
While PLD memory, read and write operation (category memo) PLD with XC2288 secured microprocessor.
The license permits reaching firmware 30 °C from the 2018 year. In addition, open access Read/Write memory for PLD, made in 2018 and later, with microprocessor Infineon XC2288.
Note: DirectConnect2 tool and License MB MEMO are needed.
PLD must be opened. The support team will fit manually.
8. License DC2
The license permits work beside the DirectConnect 2U tool (DC2) for various vehicle control modules programming without an entire vehicle system.
ISP supports Read & Write anonymous or damaged firmware from vehicle control units. BSL mode, TriCore BL mode, Motorola BKG mode, NEC serial BL ready.
Read/write MR, MCM, ACM, CPC, FR, FFR, ADM. Get a key for PLD, FFR, PTM. To have all claims, you require to have appropriate licenses.
9. License CRV
The license permits to Read/Write FLASH & EEPROMs concerning CRV1 & CRV2 engine control unit of Mercedes S, ML, GL class via OBD2.
10. License CR (CDI)
The license permits to Read/Write FLASH & EEPROMs of CDI engine control unit utilized in MB V-class, Sprinter, and Vito by the diagnostic port. CDI<>WSP matching.
11. License MCM BSL
A license to reading/Write Flash & exEEPROM of MCM, MCM2, ACM2 control units memory just covering DirectConnect 2M tool in BSL mode.
Type 1. Continental MCM (MCU TC1796-256 °F / TriCore 1 EEPROM M95640) plastic.
Type 2. Continental MCM2 (MCU TC1796-256 °F / TriCore 1 EEPROM M95128) metallic
Type 4. Continental ACM2
Note: DirectConnect 2M tool is needed. The full name of the License is MB_MCMACM_BSL.
Read mode takes about 20 minutes.
Write mode takes about 20 minutes.
12. License SFTP KEYS
EIS/MCM/TCM keys act figured for SFTP EURO6 trucks.
'Read keys info' — TCM, MCM keys status read;
MCM and TCM 'Unpairing' (Online, DC mode, tokens needed);
MCM and TCM 'Pairing' with EIS (Offline, OBD);
The license covers 600 tokens for unpairing works.
13. License SFTP CALC
MB SFTP (MP4) VeDoc calculator (X1; X2; X8).
The calculator works through OBD or via DirectConnect 2M tool.
Important! License work individually with appropriative MCM read/write license. So, for example, you could calculate VeDoc only on MCM; you could read/write. NOTE: SFTP — Strategic Future Truck Platform. The original name of MP4 EURO6 truck.
14. License IVECO VCM2
IVECO VCM2 FLASH & EEPROM memory Read/Write through OBD or via DirectConnect 2 tool connection.
15. License MB EXTRA
Speed limit R/W for PLD including FR/CPC;
Torque limit R/W;
AdBlue error delete.
16. License CPC3 EXTRA
Speed limit R/W for SFTP (MP4): MCM and CPC3.
17. License ADM EXTRA
Speed limit R/W for PLD and ADM (KAMAZ).
18. License MB DIAG
The license permits to Read DTC with the error record on MP3 and SFTP (MP4) trucks.
Clear DTC.
Read and Delete fault codes—export a full report to a PDF file.
19. License MAN DIAG
The license permits to Read DTC with the error description on MAN trucks.
Clear DTC. Read and Erase fault codes—export a full report to a PDF file.
Supported EDC7 and FFR systems.
Not supported EDC7 and PTM systems.
20. License Android
Truck Explorer Android 2.1 license. For phones (tablets), we created an Android mobile app: «Truck Explorer,» more straightforward, more helpful. The license is added, but the software must be bought in a Google Play store.
21. Update/support subscription.
Update/support subscription for 12 months is covered in a kit. After 12 months device will work, but support and update would not be given.
PACKAGE
- VEI V6 WiFi device
- USB A to USB B
- OBD2F-4-MB14 adapter
- DirectConnect 2U tool
- DC2-PLD cable
- DC2-ISP1 cable
- DC2-OBD2-Power cable
- DC2-FR+CPC+CPC4 cable
- DC2-TCM cable 2m
- DC2-TransReader13
- VEI Self test adapter
- DC2-ADM cable
- DC2U-ISP7 cable
- DC2-MCM+ACM 2m