News
15 June 2021
New feature added: now the users are to tie the USB dongle to one PC. This addition is done via authorization on the Internet when the dongle is connected the first time.
Module 77 — Bosch ME9/MED9/EDC16 Bootloader released
Module 78 — Subaru Gearbox released.
Module 77 — Bosch ME9/MED9/EDC16 Bootloader released
Module 78 — Subaru Gearbox released.
- Support of 85 other ECUs added to Module 12, «Honda/Acura CAN-bus.»
- Module 13, «Honda/Acura K-Line,» now supports new ECUs. The grouping of Keihin has been rework.
- ME17.9.1 has been added in the test stage to Module 19, with the possibility of writing and making checksum corrections.
- Module 25, «Renault/Nissan dCi,» now supports SID310 for Nissan Juke with a diesel engine of 1.5L. The support of DDCR in the test stage, reading, writing, and checksum corrections.
- Module 26, «Mitsubishi Diesel CAN-bus,» now supports ECUs with SH72543. Read, write, checksum correction via OBD.
- The support of new versions of the ECUs added to Module 27.
- Module 29, «Ford PWM,» now has checksum correction for some ECUs.
- Module 31, «Mitsubishi K-Line,» can work with MH8115 without the need for Module 24.
- The error shows the list of updates for automatic transmissions in Module 35, «Toyota/Lexus/Scion/Hino,» fixed. The support of TX2 added.
- The error with writing the modified file in Module 41 fixed.
- Now!! EEPROM 25A320/640/128 supported in Module 42. Checksum correction for some ISUZU and Nissan trucks as well as Mazda and Nissan cars added.
- EDC17CP55, MEDC17.9, and MED17.8.31 were added in a test stage in module 43.
- The error with writing the modified file in Module 44 fixed, and the support of EMD1 added.
- Module 48 now supports MED17.1.27 and MED17.1.61.
- Module 50 supports EDC17C64 for VW Crafter.
- Module 51 now supports Chery (ME17U6), Geely (MED17.8.10), and GAC (ME17.8.8.1). Reading, writing, and checksum corrections.
- Module 53 now has a feature of skipping ЕСС errors when reading, new options of checksum corrections added for CRD3/CRD3P.
- The file integrity requirements were lowered for writing a file in Module 54.
- Module 55 now supports the new Hyundai ECUs with the Euro 5 and Euro 6 requirements.
- Module 58 supports flash reading via OBD of 0CW and 0D9 and works directly with DQ200G2 of a new type.
- In Module 60, the test support of DCU102 added. Reading with a direct connection, writing via OBD, and checksum corrections.
- The support of CPEGP2.10.1/CPGPSH2.14.1 in Kia/Hyundai with petrol engines 1.0L and 1.2L added to Module 61. Reading, unlocking, writing via OBD, checksum corrections.
- Module 62 now supports TCM 6DCT451 (XPS6 Gen3) in Ford, Volvo, Renault, etc.
- Module 69 supported working with a direct connection to the ECU via CAN-bus (800Kbps) on the bench. The inability to remove DTC in some ECUs fixed.
- Module 71 now supports EDC17CP18.
- MG1CS018 and some variants of MG1CS019 are supported in Module 73.
- Module 74 now supports vehicles with diesel engines 2.4L and 2.8L.
- SID902 is in the test stage for Module 75.
- Module 76, «Kia/Hyundai Gearbox,» now supports CPTSH2.08.2 and SIM2K-143. Reading, writing, and checksum corrections.
- And other improvements.