TRUCK EXPLORER

Truck Explorer Standard equipment consists of the most general purposes for trucks. You could work via OBD or directly connect to the ECU on the board covering the DirectConnect 2U tool.

Include Licenses:

1.        License MB MEMO

The license permits to Read/Write FLASH and EEPROMs of the MR (PLD) control unit.

Additionally, it is possible to connect to the system through:

— OBD (MR is attached inside truck) or

— through connection with DirectConnect 2M tool (MR is placed on your board).

This function is handy for Chiptuning works and improving units after the broken update. OBD performs all transactions, and there is no need to decapsulate/open the unit, so the unit stays in factory position, and therefore, no guarantee is voided.

This function permits cloning MR. For example, you read one MR, save it to *.bin file, and write it to another MR.

2.        License MB KEYS

MB Keys learn — permits to figure new keys for the vehicle above OBD (MR (PLD) control unit). No extra equipment is used; all transactions are arranged offline, the only connection to the vehicle is needed.

It is possible to add a new key, delete useless keys while compared to the unit through:

— OBD (MR is attached inside truck) or

— through connection with DirectConnect 2M tool (MR is placed on your board).

Disable immobilizer within FR and MR. IMMO OFF.

3.        License MB CALC

MB VeDoc, FDOK calculators — adds entrance digests for VeDoc and FDOK algorithms for MR (PLD) control unit.

Must be practiced together with XENTRY (DAS) software and fit diagnostic tool where these codes are asked. All transactions are prepared offline—only connection to the vehicle required for VEDOC.

For FDOK calculations needed no connection to the vehicle. FDOK code for current and old DAS.

DAS password generator — calculates password required by DAS to reach some specific purposes (MR downgrade of Euro 4, 5 to Euro 3, etc. Disable AdBlue)

4.        License FR

The license permits reaching FR. Promoted FMR; FR; FR/CPC; CPC1EU; CPC2EU. Immo off in FR.

5.        License 2011+

For PLD, read and write action (category memo) PLD with XC2287 protected microprocessor, made in 2011 and following. The license permits reaching firmware 22B, 23E, 24B from 2011.

Continental Euro5 PLD: (MCU XC2287, 1 EEPROM M95640). Not locked processor supported.

*MB MEMO - license needed.

6.        License 2014+

For PLD memory, read and write transaction (category memo) PLD with XC2287 secured microprocessor.

The license permits reaching firmware 21x, 23 °F, 24 °C, 25x, 26x from the 2014 year. In addition, open access Read/Write memory for PLD, made in 2014 and following, including Infineon (XC2287) microprocessor.

Continental Euro5 PLD: 1 EEPROM M95640, MCU XC2287 (flash 768kB). Locked processor approved.

PLD must be opened. The support team will fit a manual.

*MB MEMO License and DirectConnect2M tool are needed.

7.        License 2018+

While PLD memory, read and write operation (category memo) PLD with XC2288 secured microprocessor.

The license permits reaching firmware 30 °C from the 2018 year. In addition, open access Read/Write memory for PLD, made in 2018 and later, with microprocessor Infineon XC2288.

Note: DirectConnect2 tool and License MB MEMO are needed.

PLD must be opened. The support team will fit manually.

8.        License DC2

The license permits work beside the DirectConnect 2U tool (DC2) for various vehicle control modules programming without an entire vehicle system.

ISP supports Read & Write anonymous or damaged firmware from vehicle control units. BSL mode, TriCore BL mode, Motorola BKG mode, NEC serial BL ready.

Read/write MR, MCM, ACM, CPC, FR, FFR, ADM. Get a key for PLD, FFR, PTM. To have all claims, you require to have appropriate licenses.

9.        License CRV

The license permits to Read/Write FLASH & EEPROMs concerning CRV1 & CRV2 engine control unit of Mercedes S, ML, GL class via OBD2.

10.        License CR (CDI)

The license permits to Read/Write FLASH & EEPROMs of CDI engine control unit utilized in MB V-class, Sprinter, and Vito by the diagnostic port. CDI<>WSP matching.

11.        License MCM BSL

A license to reading/Write Flash & exEEPROM of MCM, MCM2, ACM2 control units memory just covering DirectConnect 2M tool in BSL mode.

Type 1. Continental MCM (MCU TC1796-256 °F / TriCore 1 EEPROM M95640) plastic.

Type 2. Continental MCM2 (MCU TC1796-256 °F / TriCore 1 EEPROM M95128) metallic

Type 4. Continental ACM2

Note: DirectConnect 2M tool is needed. The full name of the License is MB_MCMACM_BSL.

Read mode takes about 20 minutes.

Write mode takes about 20 minutes.

12.        License SFTP KEYS

EIS/MCM/TCM keys act figured for SFTP EURO6 trucks.

'Read keys info' — TCM, MCM keys status read;

MCM and TCM 'Unpairing' (Online, DC mode, tokens needed);

MCM and TCM 'Pairing' with EIS (Offline, OBD);

The license covers 600 tokens for unpairing works.

13.        License SFTP CALC

MB SFTP (MP4) VeDoc calculator (X1; X2; X8).

The calculator works through OBD or via DirectConnect 2M tool.

Important! License work individually with appropriative MCM read/write license. So, for example, you could calculate VeDoc only on MCM; you could read/write. NOTE: SFTP — Strategic Future Truck Platform. The original name of MP4 EURO6 truck.

14.        License IVECO VCM2

IVECO VCM2 FLASH & EEPROM memory Read/Write through OBD or via DirectConnect 2 tool connection.

15.        License MB EXTRA

Speed limit R/W for PLD including FR/CPC;

Torque limit R/W;

AdBlue error delete.

16.        License CPC3 EXTRA

Speed limit R/W for SFTP (MP4): MCM and CPC3.

17.        License ADM EXTRA

Speed limit R/W for PLD and ADM (KAMAZ).

18.        License MB DIAG

The license permits to Read DTC with the error record on MP3 and SFTP (MP4) trucks.

Clear DTC.

Read and Delete fault codes—export a full report to a PDF file.

19.        License MAN DIAG

The license permits to Read DTC with the error description on MAN trucks.

Clear DTC. Read and Erase fault codes—export a full report to a PDF file.

Supported EDC7 and FFR systems.

Not supported EDC7 and PTM systems.

20.        License Android

Truck Explorer Android 2.1 license. For phones (tablets), we created an Android mobile app: «Truck Explorer,» more straightforward, more helpful. The license is added, but the software must be bought in a Google Play store.

21.        Update/support subscription.

Update/support subscription for 12 months is covered in a kit. After 12 months device will work, but support and update would not be given.

PACKAGE

• VEI V6 WiFi device
  
• USB A to USB B
  
• OBD2F-4-MB14 adapter
  
• DirectConnect 2U tool
  
• DC2-PLD cable
• DC2-ISP1 cable
• DC2-OBD2-Power cable
• DC2-FR+CPC+CPC4 cable
• DC2-TCM cable 2m
• DC2-TransReader13
• VEI Self test adapter
• DC2-ADM cable
• DC2U-ISP7 cable
• DC2-MCM+ACM 2m

The truck Explorer Revolution kit is best for the specialists who were starting work with trucks. It is because it has popular functions to work over OBD. However, if you prefer to work on the bench, please choose a Standard V6 kit or add a DirectConnect2U tool.

The Revolution kit updated from 2021-02-01.

Licenses in a kit:

1- License MB MR
PLD (MR) external FLASH & EEPROMs Read&Write; Checksum

2-  License MB KEYS
Key programming for Mercedes truck (MR) by OBDKey programming on PLD (MR). IMMO OFF on MR and FR/CPC

3-  License MB CALC
Calculate codes for VeDoc ( X1, X2, X8); FDOK (XT, XS, XN) algorithms, DAS password

4-  License MR+
MB MR; MB KEYS; MB CALC functionality with PLD MCU XC2287, XC2288H.
Supported Firmware: 22B; 23E; 24B, 23F; 24C; 25B, 30C, 25C, 31B

5-  License FR
FR&CPC - C167, ST10F276 Flash & EEPROM R/W. OBD and DC mode

6-  License pack EXTRA
- License MB EXTRA
- License CPC3 EXTRA
- License ADM EXTRA
Speed limit R/W for PLD and FR; Torque limit R/W; AdBlue error Erase Speed limit R/W for MCM and CPC3; SFTP Speed limit R/W for ADM3;

7-  License MB DIAG
MB Fault codes DTC Read/Erase; All code descriptions; Generate Full report in PDF file

8-  License MAN KEYS
Key programming for MAN trucks FFR or PTM over OBD or DC2.
Paring by OBD: EDC7U32+FFR, EDC7U32+PTM, MS6.x+FFR
Paring by DC2 with cable: EDC7U32+FFR, EDC7U32+PTM

9-  License MAN DIAG
MAN Fault codes DTC Read/Erase; All code descriptions. OBD/DC2

10-  License Android
Truck Explorer Android license

11- Tokens for operations
Additional operations for tokens (price per operation)

Support and updates for 12 months included.
Warranty for hardware 12 months.
Included tokens: 100 (Operations and prices)

PACKAGE

• VEI V6 WiFi main tool
• USB A-B cable
  
• OBD2F-4-MB14 adapter
  
• OBD2F-4-MN12 adapter
  
• VEI Self Test cable
  

The MBench Lite
An additional for Truck Explorer.

Function:
- Engine emulator for PLD (MR) system.

Inside:
Supported PLD all hardware types: A1 - A7;
Supported PLD all firmware versions;
Pumps-injectors emulator. R4; R6; V6; V8
Oil sensor emulator;
Crankshaft, Camshaft emulator;
Starter circuit emulator;
Other emulators;
Compatible with Truck Explorer software from v5.6

MBench BENEFITS:
Engine emulator on your table;
The complete test of PLD ECU before test inside the Truck;
Easy to use in your workplace;
Save the place on your table;
Reduce repair time by 70%;
Improving experience and education of ECU repair knowledge

All emulated loads are static and represent resistive load - 50 Ohm.
MBench emulates the following loads for MR-PLD:
N3_xx is several pins in 55 pins connector on the MR-PLD unit:
N3_18 --- Starter (Highside)
N3_12 --- Proportional Valve Bank (Supply PV 1...4)
N3_43 --- Proportional Valve 4 (Lowside Y71 - Fan Stage 1 Solenoid)
N3_41 --- Proportional Valve 3 (Lowside Y70 - Fan Stage 1 Solenoid)
N3_50 --- Proportional Valve 2 (Lowside Y49 - Hydraulic Solenoid)
N3_52 --- Proportional Valve 2 (Supply Y49 - Hydraulic Solenoid )
N3_51 --- Proportional Valve 1 (Lowside - Engine Retarder Flap)
N3_11 --- Proportional Valve - Ground
N3_27 --- Proportional Valve 5 (Highside - Digital Output)
N3_40 --- Proportional Valve 6 (Lowside - Engine Retarder Flap)
N3_42 --- Proportional Valve 6 (Supply - Engine Retarder Flap)
Other loads not present in a device.

DirectConnect 2U tool (DC2U)

For various vehicle control modules programming without a complete vehicle system. 

ISP helps Read & Write unknown or damaged firmware from vehicle control units.

BSL mode, TriCore BL mode, Motorola BKG mode, NEC serial BL ready.

Supported: J1708, BSL UART, SPI (SCI), MBench.

The License EHZ

(E-MAS) Flash & EEPROM Read/Write by DirectConnect2 in BSL mode. It is not necessary to open ECU.

•  DC2-EHZ cable not included.

Supported microprocessors:
MCU: 10F269
MCU: C167CS

Supported models:
DAF EMAS-ECU
Mercedes EHZ VSE EMAS-ECU

The License pack MCM2

License MCM2 DC
Function:
Read / Write MCM2 (IntFLASH of TC1796; IntEEPROM; ExtEEPROM) in DC mode (on bench by cable)

Supports MCM2 versions:
Type 1. Continental MCM2 (MCU TC1796-256F / TriCore 1 EEPROM M95640).
Type 2. Continental MCM2 (MCU TC1796-256F / TriCore 1 EEPROM M95128).

The difference between OBD, BSL, and DC modes:
OBD mode is a software mode by diagnostic port OBDII.
Advantage: Fast - 5 minutes.; No need to disconnect or open ECU.
Disadvantage: Could not read damaged ECU.

BSL mode is a BootStrap Loader mode. (Safe mode for ECU).
Advantage Could read/write damaged ECU. ECU recovery. No need to open ECU.
Disadvantage: Slow. 30 min to read/write.
Checksum not available in BSL mode

DC mode is a software mode.
Advantage: Fast - 5 minutes.; No need to open ECU.
Disadvantage: Could not read damaged ECU.

License MCM2 OBD
The license allows to:
Read / Write MCM2 (IntFLASH of TC1796; ExtEEPROM) by OBD2 in Software mode.
The procedure takes 5 minutes.

Supports MCM2 version.

Needed (not included in a price):
VEI device
License MB MEMO
Valid Update/support subscription
Software version from 5.6

The License pack MCM

License MCM DC
MCM - Flash & EEPROM Read/Write by DC in Software mode.

License MCM OBD
The license allows to:
Read / Write MCM (IntFLASH of TC1796; ExtEEPROM) by OBD2 in Software mode.
The procedure takes 5 minutes.

Supports only MCM (MCM1) version.

Needed (not included in a price):
VEI device
License MB MEMO
Valid Update/support subscription
Software version from 5.6

The License CR

It's needed for Read & Write FLASH & EEPROMs of CRV1 & CRV2 engine control unit of Mercedes S, ML, GL class via OBD2.

Read/Write FLASH & EEPROMs of CDI engine control unit.
MB V-class, Sprinter, and Vito thru the diagnostic port.
CDI<->WSP pairing.

The License pack MCM2.1
MCM2.1 Flash & EEPROM Read/Write
MCM2.1 (locked / unlocked)
Supported HW: D1, D2, D3
HW: D4 - not supported

License MCM2.1 DC
The license allows to Read / Write MCM2.1 (IntFLASH of TC1797; IntEEPROM; ExtEEPROM) via DirectConnect 2 tool in Software mode.
The procedure takes 5 minutes.

Supports MCM2.1 versions:
1) Unlocked (without password) until 2016/4
2) Locked (with password) from 2016/4 - up 2019/04 (D2.x, D3)

Not supported MCM2.1 versions:
1) Locked (with password) from 2019/04 (HW: D4)

License MCM2.1 OBD
The license allows to Read / Write MCM2.1 (IntFLASH of TC1797; ExtEEPROM) by OBD2 in Software mode.

Supports MCM2.1 versions:
1) Unlocked (without password) until 2016/4
2) Locked (with password) from 2016/4 - up 2019/04 (D2.x, D3)

Not supported MCM2.1 versions:
1) Locked (with password) from 2019/04 - up today (HW: D4)

The procedure takes ~5 minutes.

Needed (not included in a price):
VEI device
DirectConnect 2 tools with DC2-MCM adapter
License MB MEMO
License MB MCM2.1 DC
License DC2
Valid Update/support subscription
Software version from 5.6

The License SFTP CALC

Function:
MB SFTP (MP4) VeDoc/Fdok XS; XT; XN; X1; X2; X8 calculator

Note:
VeDoc Calculator works only on that MCM, which license for MCM MEMO read/write you have.
MB CALC license is needed.

The License pack PTM
It's for Read/Write Flash/Flash.

Read/write of:
- MPC Microprocessor Controller MPC5554 (SPC6670) (Flash)
- External flash M29W160EB (Flash)

Operation modes:
- OBD
- DC
- JTAG (new, included in a pack from 2021-01-11)
In DC mode: No need to disassemble ECU.

Cable needed:
- DC2-PTM cable or DC2-EDC7+PTM+FFR cable
In JTAG mode: Need to disassemble ECU.

Need for additional cables:
- DC2U-ISP-JTAG+BDM dongle
- DC2U-JTAG8 open flex cable

Read FLASHs procedure takes ~20 min.

License PTM OBD
MAN PTM Flash&Flash read/write by OBD
Read/write of:
- MPC Microprocessor Controller MPC5554 (SPC6670) (Flash)
- External flash M29W160EB (Flash)

All operations are doing by OBD connection to MAN truck.
No need to disassemble ECU.
No need for soldering.
No need for special education.
Read FLASHs procedure takes 30 min.

License PTM DC
PTM Flash&Flash read/write by DirectConnect2 tool and TruckExplorer V6 tool.
Read/write of:
- MPC Microprocessor Controller MPC5554 (SPC6670) (Flash)
- External flash M29W160EB (Flash)

All operations are doing on a bench.
No need to disassemble ECU.
No need for soldering.
No need for special education.
Read FLASHs procedure takes 30 min.

License PTM JTAG
PTM Flash&Flash read/write by DirectConnect2 tool and TruckExplorer V6 tool in JTAG mode.

Read/write of:
- MPC Microprocessor Controller MPC5554 (SPC6670) (Flash)
- External flash M29W160EB (Flash)

All operations are doing on a bench.
Required for disassemble ECU!!!
Required for additional wires!!!
Read FLASHs procedure takes ~20 min.


Needed (not included in a price):
- VEI V6 tool
- Software version greater than v6.15
- DC2 (DC2M or DC2U) tool
- DC2-PTM cable or DC2-EDC7+PTM+FFR cable
- DC2U-ISP-JTAG+BDM dongle
- DC2U-JTAG8 open flex cable

The License pack MAN EDC7

It's for EDC7C32:
License MAN EDC7 OBD - Flash R/W by OBD; AutoChecksum.
License MAN EDC7 GPT - Bootloader/Flash/EEPROM R/W in GPT mode; Flash R/W in DC mode. AutoChecksum.
License EDC7 BDM - Bootloader/Flash/EEPROM R/W in BDM mode.

Operation modes:

OBD mode for EDC7C32:
1) Read / Write Flash only.
2) Checksum
3) Parameters change
4) Fault codes read/erase

DC mode for EDC7C32:
1) Read / Write Flash only.
2) Checksum
3) Parameters change
4) Fault codes read/erase
5) No need to open ECU.

DC GPT mode for EDC7C32:
1) Read / Write Bootloader, Flash, and EEPROM.
2) Auto Checksum before the write operation.
3) No need to open ECU.
4) Parameters change
5) Fault codes read/erase

DC BDM mode for EDC7C32:
1) Need to open ECU.
2) Read / Write Bootloader, Flash, and EEPROM.
3) For recovery. No Checksum.



License MAN EDC7 OBD
The license enables a function to read/write FLASH of MAN EDC7 by OBD.
Supported versions:
EDC7C3 from MAN truck
EDC7C32 from MAN truck
EEPROM read/write is not available.



License MAN EDC7 GPT
License EDC7 DC upgraded to Licenses MAN EDC7 GPT.
License MAN EDC7 GPT supported EDC7C32 - Flash and EEPROM Read / Write by DC2U in GPT mode.
1) FLASH: MPC562, 2048 KB;
2) EEPROM A: 95640, 8 KB
Auto Checksum before Write operation.
In DC GPT mode: No need to disassemble ECU.

Needed (not included in a price):
VEI V6
DC2U tool
DC2U-EDC7C32 GPT cable
License MAN EDC7 GPT
Software v6.17



License EDC7 BDM
License EDC7 BDM - Flash/EEPROM R/W by DC BDM mode.
Recover MPC562 by DC2U in BDM mode
In DC BDM mode for MAN EDC7C32:
1) Need to open ECU.
2) Read / Write Flash and EEPROM.
In DC BDM mode for IVECO EDC7UC32:
1) Need to open ECU.
2) Read / Write Flash and EEPROM.

Needed (not included in a price):
DC2U-ISP-JTAG+BDM dongle for DC2U
DC2U-BDM10 to MHD10 cable (for dongle)
DC2U-EDC7C32 GPT
DC2U-BDM7 open flex cable (for dongle)
DC2U-EDC7UC31 GPT

The License IVECO CALC

IVECO VCM2 PIN calculation by DC2.
PIN code used to start an IVECO truck without a key.

Supported VCM2 version: Infineon TriCore TC1765 CPU
The license works in Truck Explorer v6.12 software and with VEI V6.

Note: IVECO Key programming in Truck Explorer is not available for now.

The License pack MCM BSL
Flash & EEPROM Read/Write by DC2 in BSL
MCM, MCM2, ACM2, ACM2.1 (unlocked)
MCM2.1 (unlocked)

License MCM/ACM BSL
Supported functions:
- Read & Write MCM, MCM2, ACM2, ACM2.1 (without password) control units memory (IntFLASH; IntEEPROM; ExtEEPROM) with DirectConnect 2 tool in BSL MODE.

Supports Continental MCM/ACM:
1. Continental MCM (MCU TC1796-256F / TriCore 1 EEPROM M95640).
2. Continental MCM2 (MCU TC1796-256F / TriCore 1 EEPROM M95128).
3. Continental ACM2 (MCU TC1796-256F / TriCore 1 EEPROM M95128).
4. Continental ACM2.1 (without password) (MCU TC1796-256F / TriCore 1 EEPROM M95128).

Important:
In BSL mode, the Checksum correction of a flash file is impossible. Therefore, please make the checksum of the BIN file before writing to ECU.
The checksum is done in DC or OBD mode.
Use BSL mode only in emergency mode.
Keys learning is not supported.
You need DirectConnect 2 and DC2-MCM adapter.

Full Connection:
Laptop -> VEI -> DirectConnect 2 tool -> DC2-MCM adapter -> MCM/ACM ECU

Important!
ACM2.1 (with password) is not supported. Need additional license ACM2.1 OBD or ACM2.1 DC.
MCM2.1 is not supported. Need additional License MCM2.1 BSL, or MCM2.1 DC, or MCM2.1 OBD

License MCM2.1 BSL
The license allows to Read / Write MCM2.1 (IntFLASH of TC1797; IntEEPROM; ExtEEPROM) via DirectConnect 2 tool in BSL mode.

Supported MCM2.1 versions:
1) Unlocked (without password) until 2016/4

Not supported MCM2.1 versions (ECU does not have BSL mode):
1) Locked (with password) from 2016/4 - up 2019/06 (HW: D2.x, D3)
2) Locked (with password) from 2019/6 - up today (HW: D4)

Important:
In BSL mode, the Checksum correction of a flash file is impossible. Therefore, please make the checksum of the BIN file before writing to ECU.
The checksum is done in DC or OBD mode.
Use BSL mode only in emergency mode.

Needed (not included in a price):
VEI device
DirectConnect2 tool with DC2-MCM adapter
License MB MEMO
License DC2
Valid Update/support subscription
Software version from 5.3

The License CPC3

CPC3-DC mode: CPC3 read/write by DC2U and DC2-CPC3 cable. No need to disassemble ECU.
- Full Flash MPC5566
- Full Eeprom AT25256

Needed (not included in a price):
VEI V6 device
DirectConnect 2U tool - 800 USD
DC2-CPC3 cable - 540 USD

CPC3-JTAG mode: CPC3 read/write flash/EEPROM in DC2 JTAG mode. It's Needed to disassemble ECU.For recover CPC3.
Read/write full flash and EEPROM:
- Full Flash MPC5566
- Full Eeprom AT25256
It is needed to disassemble ECU.
It is needed for additional wires.

Hardware needed (not included in a price):
VEI V6 device
DirectConnect 2U tool - 800 USD (Only adapter)
DC2-CPC3 cable - 540 USD
DC2U-ISP-JTAG+BDM dongle - 420 USD
DC2U-JTAG8 open flex cable - 70 USD

The License pack ACM2.1
ACM2.1 (locked/unlocked) Flash & EEPROM Read/Write

License ACM2.1 DC
The license allows to Read / Write ACM2.1 (IntFLASH of TC1796; IntEEPROM; ExtEEPROM) via DirectConnect 2 tool in Software mode.

Supports ACM2.1 versions:
1) Unlocked (without password) until 2016/4
2) Locked (with password) 2017 year (from 2016/4 - up today).

License ACM2.1 OBD
The license allows to Read / Write ACM2.1 (IntFLASH of TC1796; ExtEEPROM) by OBD2 in Software mode.
The procedure takes 5 minutes.

Supports ACM2.1 versions:
1) Unlocked (without password) until 2016/4
2) Locked (with password) from 2016/4 - up today


Needed (not included in a price):
VEI device
DirectConnect 2 tool with DC2-MCM adapter
License MB MEMO
License DC2
Valid Update/support subscription
Software version from 5.6

The License pack FFR

License MAN FFR
License FFR is for Read & Write FLASH & EEPROMs (C167 and ST10Fxx microprocessors) of drive control modules FFR (MAN).
Operations are available over OBD connection or via DirectConnect 2M.

License MAN FFR BSL
FFR - Flash & EEPROM Read / Write in BSL mode

External FLASH (AM29Fx00) and EEPROM R/W in Boot mode.
Via DirectConnect 2 box ISP port.

Functions available for all FFR models. In BSL mode, Flash and EEPROM reading available for all versions of FFR firmware.

Supported all unknown (for Truck Explorer License FFR) versions and damaged FFR versions.

Needed (not included in a price):
DirectConnect 2U kit - 1150 USD

The License pack ACM2

License ACM2 DC
The license allows to Read / Write ACM2 (IntFLASH of TC1796; IntEEPROM; ExtEEPROM) via DirectConnect 2 tool in Software mode.

Supports ACM2 version:
Continental ACM2 (MCU TC1796-256F / TriCore 1 EEPROM M95128).

License ACM2 OBD
The license allows to Read / Write ACM2 (IntFLASH of TC1697; ExtEEPROM) by OBD2 in Software mode. The procedure takes 5 minutes.

Supports ACM2 version.


Needed (not included in a price):
VEI device
DirectConnect 2 with DC2-MCM adapter
License MB MEMO
Valid Update/support subscription
Software version from 5.6
License DC2

The license pack GS2 

 Allows to Read / Write automatic gearbox GS2 (EPS3) ECU flash/EEPROM.
Electronic Control Unit and type: GS2 (EPSIII) made by WABCO
Functionality:
1) Read / Write ECU memory with DirectConnect 2U (or 2M) tool in standalone mode.
2) Standalone diagnostics.
Supports GS2 (EPSIII) version:
- FLASH: ST10F273 512 KB
- EEPROM A: 2KB
Supported CPU: C167CS, 10F276

License GS2 DC
The license pack GS2 allows to Read / Write automatic gearbox GS2 (EPS3) ECU flash/EEPROM.
Electronic Control Unit and type: GS2 (EPSIII) made by WABCO
Functionality:
1. Read / Write ECU memory with DirectConnect 2U (or 2M) tool in standalone mode.
2. Standalone diagnostics.
Supports GS2 (EPSIII) version:
- FLASH: ST10F273 512 KB
- EEPROM A: 2KB

Supported CPU: C167CS, 10F276

License GS2 BSL
Gearbox ECU GS2 (EPS3) Flash/EEPROM Read/Write by DC2 in BSL mode.
Supported MCU ST10F276:
- FLASH: ST10F276, 832 KB
- EEPROM A: 93C86, 2 KB
Supported MCU C167CS:
- FLASH: C167CS
- EEPROM A
Need open ECU.

Needed (not included in a price):
VEI V6 device
DirectConnect 2U or 2M tool - 800 USD (Only adapter)
DC2-GS2 cable - 350 USD
DC2-ISP6 cable for BSL mode - 120 USD
Software version 6.0 or newest
Laboratory power supply 24VDC 3A

The License SFTP KEYS
 It provides for pairing optical keys (EIS) to TCM and MCM2 (MCM2.1). So you could take a used TCM (or MCM), unpair it, and put it on any SFTP truck (Mercedes MP4). Optical keys will be programming to unpaired TCM (or MCM) with the PAIRING function. What to do if all keys a missing 

Software module: SFTP KEYS (Optical key programming on SFTP)
Software version release: v6.12 (2019-12-02), v6.14 (2020-06-05), New: v6.16 (2021-02-24)
Brand: Mercedes; Detroit Diesel
Vehicle type: Trucks; Buses
Affected electronical control units: EIS01; MCM2; MCM2.1 (D2.x; D3.x); TCM01T (WABCO/FESTO)
Description: SFTP KEYS managing the Immobilizer system of SFTP (generation 4) trucks and buses. Immobilizer diagnostic, adaptation, and repair.

Functionality:
Key+EIS+MCM+TCM immobilizer Info Read;
MCM, TCM unpairing (internet and active tokens needed);
EIS+MCM+TCM pairing by OBD (offline);
Optical key diagnostic;
Transponder key programming to MCM.
Switch from Classic to FBS3 mode
Switch from FBS3 to Classic mode
Information updated: 2021-02-25
UNPAIRING function: Tokens needed. Online. Only DC mode.
PAIRING function: Tokens no needed. Offline. Only OBD mode.
Transponder key programming: No Tokens needed. Offline. OBD mode only
Tokens: 600 tokens included in the license price

License SFTP KEYS functions:
TCM Unpair (virgin) - need online! 100 Tokens
MCM Unpair (virgin) - need online! 50 Tokens
MCM Pair (by OBD) free
TCM Pair (by OBD) free
MCM Switch from Classic to FBS3 mode 60 Tokens
MCM Switch from FBS3 to Classic mode 60 Tokens
MCM Add new key with transponder free

Needed (not included in a price):
VEI V6
DC2U kit -
DC2U-TCM cable -
DC2U-ACM/MCM cable -
Software versions from v6.12
Active Tokens for Online UNPAIR function